Maytag Clothes Dryer W10155111A User Manual

GAS DRYER  
USE & CARE GUIDE  
FOR QUESTIONS ABOUT FEATURES, OPERATION/PERFORMANCE, PARTS, ACCESSORIES OR SERVICE CALL: 1.800.688.9900  
VISIT OUR WEBSITE AT WWW.MAYTAG.COM  
W10155111A  
 
WARNING: For your safety, the information in this manual must be followed to minimize  
the risk of fire or explosion, or to prevent property damage, personal injury, or death.  
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this  
or any other appliance.  
WHAT TO DO IF YOU SMELL GAS:  
Do not try to light any appliance.  
Do not touch any electrical switch; do not use any phone in your building.  
Clear the room, building, or area of all occupants.  
Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's  
instructions.  
If you cannot reach your gas supplier, call the fire department.  
Installation and service must be performed by a qualified installer, service agency, or  
the gas supplier.  
In the State of Massachusetts, the following installation instructions apply:  
Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by  
the State of Massachusetts.  
If using a ball valve, it shall be a T-handle type.  
A flexible gas connector, when used, must not exceed 3 feet.  
3
 
IMPORTANT SAFETY INSTRUCTIONS  
WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic precautions,  
including the following:  
Read all instructions before using the dryer.  
Do not repair or replace any part of the dryer or attempt  
any servicing unless specifically recommended in this  
Use and Care Guide or in published user-repair  
instructions that you understand and have the skills to  
carry out.  
Do not place items exposed to cooking oils in your dryer.  
Items contaminated with cooking oils may contribute to  
a chemical reaction that could cause a load to catch fire.  
Do not dry articles that have been previously cleaned in,  
washed in, soaked in, or spotted with gasoline, dry-  
cleaning solvents, or other flammable or explosive  
substances as they give off vapors that could ignite or  
explode.  
Do not use fabric softeners or products to eliminate static  
unless recommended by the manufacturer of the fabric  
softener or product.  
Do not use heat to dry articles containing foam rubber or  
similarly textured rubber-like materials.  
Do not allow children to play on or in the dryer. Close  
supervision of children is necessary when the dryer is  
used near children.  
Clean lint screen before or after each load.  
Keep area around the exhaust opening and adjacent  
surrounding areas free from the accumulation of lint, dust,  
and dirt.  
Before the dryer is removed from service or discarded,  
remove the door to the drying compartment.  
The interior of the dryer and exhaust vent should be  
cleaned periodically by qualified service personnel.  
Do not reach into the dryer if the drum is moving.  
Do not install or store the dryer where it will be exposed  
to the weather.  
See installation instructions for grounding requirements.  
Do not tamper with controls.  
SAVE THESE INSTRUCTIONS  
IMPORTANT: The gas installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas  
Code, ANSI Z223.1/NFPA 54.  
The dryer must be electrically grounded in accordance with local codes, or in the absence of local codes, with the National  
Electrical Code, ANSI/NFPA 70.  
4
 
INSTALLATION INSTRUCTIONS  
Tools and Parts  
Location Requirements  
Gather the required tools and parts before starting installation. Read and follow the  
instructions provided with any tools listed here.  
WARNING  
8" or 10" pipe wrench  
Level  
8" or 10" adjustable  
wrench (for gas  
connections)  
Knife  
Vent clamps  
Pipe-joint compound  
resistant to LP gas  
Flat-blade screwdriver  
Adjustable wrench that  
opens to 1" (2.5 cm) or  
hex-head socket wrench  
(for adjusting dryer feet)  
Caulking gun and  
compound (for installing  
new exhaust vent)  
Explosion Hazard  
Keep flammable materials and vapors, such as  
gasoline, away from dryer.  
Pliers  
¼" nut driver or socket  
wrench (recommended)  
Place dryer at least 18 inches (46 cm) above the floor  
for a garage installation.  
Tape measure  
Failure to do so can result in death, explosion, or fire.  
Parts supplied:  
Remove parts package from dryer drum. Check that all parts were included.  
You will need  
A location that allows for proper exhaust installation. A gas dryer must be exhausted to  
the outdoors. See “Venting Requirements.”  
A grounded electrical outlet located within 2 ft (61 cm) of either side of the dryer. See  
“Electrical Requirements.”  
4 leveling legs  
A sturdy floor to support the dryer with a total weight (dryer and load) of 200 lbs (90.7 kg).  
The combined weight of a companion appliance should also be considered.  
Parts needed:  
Check local codes and consult gas supplier. Check existing gas supply, electrical supply and  
venting, and read “Electrical Requirements,” “Gas Supply Requirements” and “Venting  
Requirements” before purchasing parts.  
A level floor with a maximum slope of 1" (2.5 cm) under entire dryer. (If slope is greater  
than 1" [2.5 cm], install Extended Dryer Feet Kit, Part Number 279810.) Clothes may not  
tumble properly and dryers with automatic sensor cycles may not operate correctly if  
dryer is not level.  
Mobile home installations require special parts (listed following) that may be ordered by  
calling the dealer from whom you purchased your dryer. For further information, please refer  
to the “Assistance or Service” section.  
Do not operate your dryer at temperatures below 45ºF (7ºC). At lower temperatures, the dryer  
might not shut off at the end of an automatic cycle. Drying times can be extended.  
Mobile Home Installation Kit. Ask for Part Number 346764.  
Metal exhaust system hardware.  
The dryer must not be installed or stored in an area where it will be exposed to water and/or  
weather.  
Check code requirements. Some codes limit, or do not permit, installation of the dryer in  
garages, closets, mobile homes, or sleeping quarters. Contact your local building inspector.  
NOTE: No other fuel-burning appliance can be installed in the same closet as a dryer.  
5
 
Companion appliance spacing should also be considered.  
Installation Clearances  
The location must be large enough to allow the dryer door to open fully.  
3"*  
(7.6 cm)  
Dryer Dimensions  
14" max.  
(35.6cm)  
*
48 in.2  
*
(310 cm2 )  
18"*  
(45.7 cm)  
2
43½"  
(110.5cm)  
24 in.  
*
3"  
*
(155 cm2 )  
(7.6 cm)  
1"  
(2.5 cm)  
1"  
(2.5 cm)  
1"*  
29¼"  
27"  
(68.6 cm)  
5"  
(14 cm)  
(2.5 cm) (74.3 cm)  
A
C
B
14³⁄₁₆"  
(36cm)  
A. Recessed area  
*29¼"  
(74.3cm)  
B. Side view - closet or confined area  
C. Closet door with vents  
27"  
(68.6cm)  
*Required spacing  
*Most installations require a minimum 5" (12.7 cm) clearance behind the dryer for the  
exhaust vent with elbow. See “Venting Requirements.”  
Mobile Home - Additional Installation Requirements  
This dryer is suitable for mobile home installations.  
The installation must conform to the Manufactured Home Construction and Safety Standard,  
Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and  
Safety, Title 24, HUD Part 280).  
Installation spacing for recessed area or closet installation  
The following spacing dimensions are recommended for this dryer. This dryer has been tested  
for spacing of 0" (0 cm) clearance on the sides and rear. Recommended spacing should be  
considered for the following reasons:  
Mobile home installations require:  
Additional spacing should be considered for ease of installation and servicing.  
Additional clearances might be required for wall, door and floor moldings.  
Additional spacing should be considered on all sides of the dryer to reduce noise transfer.  
Metal exhaust system hardware, which is available for purchase from your dealer.  
Mobile home Installation Kit Part Number 346764. See “Tools and Parts” section for  
information on ordering.  
For closet installation, with a door, minimum ventilation openings in the top and bottom  
of the door are required. Louvered doors with equivalent ventilation openings are  
acceptable.  
Special provisions must be made in mobile homes to introduce outside air into the dryer.  
The opening (such as a nearby window) should be at least twice as large as the dryer  
exhaust opening.  
6
 
Electrical Requirements  
Gas Supply Requirements  
WARNING  
WARNING  
Electrical Shock Hazard  
Explosion Hazard  
Use a new CSA International approved gas supply line.  
Install a shut-off valve.  
Plug into a grounded 3 prong outlet.  
Do not remove ground prong.  
Do not use an adapter.  
Securely tighten all gas connections.  
If connected to LP, have a qualified person make sure  
gas pressure does not exceed 13" (33 cm) water  
column.  
Do not use an extension cord.  
Failure to follow these instructions can result in death,  
fire, or electrical shock.  
Examples of a qualified person include:  
licensed heating personnel,  
authorized gas company personnel, and  
authorized service personnel.  
120 Volt, 60 Hz., AC only, 15- or 20-amp fused electrical supply is required. A time-delay  
fuse or circuit breaker is recommended. It is also recommended that a separate circuit  
serving only this dryer be provided.  
Failure to do so can result in death, explosion, or fire.  
GROUNDING INSTRUCTIONS  
Gas Type  
For a grounded, cord-connected dryer:  
This dryer must be grounded. In the event of malfunction or  
breakdown, grounding will reduce the risk of electric shock  
by providing a path of least resistance for electric current.  
This dryer is equipped with a cord having an equipment-  
grounding conductor and a grounding plug. The plug must  
be plugged into an appropriate outlet that is properly  
installed and grounded in accordance with all local codes  
and ordinances.  
Natural Gas:  
This dryer is equipped for use with Natural gas. It is design-certified by CSA International for  
LP (propane or butane) gases with appropriate conversion.  
Your dryer must have the correct burner for the type of gas in your home. Burner  
information is located on the rating plate in the door well of your dryer. If this information  
does not agree with the type of gas available, contact your dealer or call the phone  
numbers referenced on the front page of this manual.  
LP gas conversion:  
Conversion must be made by a qualified technician.  
WARNING: Improper connection of the equipment-  
grounding conductor can result in a risk of electric shock.  
Check with a qualified electrician or service representative  
or personnel if you are in doubt as to whether the dryer is  
properly grounded. Do not modify the plug provided with the  
dryer: if it will not fit the outlet, have a proper outlet installed  
by a qualified electrician.  
No attempt shall be made to convert the appliance from the gas specified on the model/serial  
rating plate for use with a different gas without consulting your gas company.  
Gas supply line  
Must include ¹⁄₈" NPT minimum plugged tapping accessible for test gauge connection,  
SAVE THESE INSTRUCTIONS  
immediately upstream of the gas connection to the dryer. See illustration.  
¹⁄₂" IPS pipe is recommended.  
7
 
³⁄₈" approved aluminum or copper tubing is acceptable for lengths under 20 ft (6.1 m) if  
local codes and gas supplier permit.  
Dryer Gas Pipe  
If you are using Natural gas, do not use copper tubing.  
The gas pipe that comes out through the rear of your dryer has a ³⁄₈" male pipe thread.  
Lengths over 20 ft (6.1 m) should use larger tubing and a different size adapter fitting.  
If your dryer has been converted to use LP gas, ³⁄₈" LP compatible copper tubing can be  
used. If the total length of the supply line is more than 20 ft (6.1 m), use larger pipe.  
6¼"  
B
(15.88 cm)  
NOTE: Pipe-joint compounds that resist the action of LP gas must be used. Do not use  
TEFLON®† tape.  
Must include a shutoff valve:  
An individual shutoff valve must be installed within 6 feet  
(1.8 m) of the dryer in accordance with the National Fuel Gas Code, ANSI Z223.1. The  
location should be easy to reach for opening and closing.  
1½"  
(3.81 cm)  
A
C
E
A
A. ½" NPT gas supply line  
B. ³⁄₈" NPT dryer pipe  
D
B
Venting Requirements  
A. ³⁄₈" flexible gas connector  
B. ³⁄₈" pipe to flare adapter fitting  
C. ¹⁄₈" NPT minimum plugged tapping  
D. ½" NPT gas supply line  
WARNING  
E. Gas shutoff valve  
Gas supply connection requirements  
Use an elbow and a ³⁄₈" flare x ³⁄₈" NPT adapter fitting between the flexible gas connector  
and the dryer gas pipe, as needed to avoid kinking.  
Fire Hazard  
Use a heavy metal vent.  
Use only pipe-joint compound. Do not use TEFLON®† tape.  
This dryer must be connected to the gas supply line with a listed flexible gas connector  
that complies with the standard for connectors for gas appliances, ANSI Z21.24.  
Do not use a plastic vent.  
Do not use a metal foil vent.  
Burner input requirements  
Failure to follow these instructions can result in death  
or fire.  
Elevations above 10,000 ft (3,048 m):  
When installed above 10,000 ft (3,048 m) a 4% reduction of the burner Btu rating shown  
on the model/serial number plate is required for each 1,000 ft (305 m) increase in  
elevation.  
WARNING: To reduce the risk of fire, this dryer MUST BE EXHAUSTED OUTDOORS.  
IMPORTANT: Observe all governing codes and ordinances.  
Gas supply pressure testing  
The dryer exhaust must not be connected into any gas vent, chimney, wall, ceiling or a  
concealed space of a building.  
The dryer must be disconnected from the gas supply piping system during pressure testing  
at pressures greater than ½ psi.  
®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.  
8
 
Clamps  
If using an existing vent system  
Use clamps to seal all joints.  
Exhaust vent must not be connected or secured with screws or other fastening devices  
that extend into the interior of the duct. Do not use duct tape.  
Clean lint from the entire length of the system and make sure exhaust hood is not plugged  
with lint.  
Replace any plastic or metal foil vent with rigid or flexible heavy metal vent.  
Review Vent system chart. Modify existing vent system if necessary to achieve the best  
drying performance.  
Clamp  
If this is a new vent system  
Exhaust  
Recommended hood styles are shown here.  
Vent material  
Use a heavy metal vent. Do not use plastic or metal foil vent.  
B
4" (10.2 cm) heavy metal exhaust vent and clamps must be used.  
A
4"  
(10.2 cm)  
4"  
10.2 cm  
4"  
(10.2 cm)  
4" (10.2 cm) heavy metal exhaust vent  
A. Louvered hood style  
B. Box hood style  
Vent products can be purchased from your dealer or by calling Maytag Services. For more  
information, see the “Assistance or Service” section.  
The angled hood style (shown here) is acceptable.  
Rigid metal vent  
For best drying performance, rigid metal vents are recommended.  
Rigid metal vent is recommended to avoid crushing and kinking.  
4"  
(10.2 cm)  
Flexible metal vent  
Flexible metal vents are acceptable only if accessible for cleaning.  
2½"  
(6.4 cm)  
Flexible metal vent must be fully extended and supported when the dryer is in its final  
location.  
An exhaust hood should cap the vent to keep rodents and insects from entering the home.  
Remove excess flexible metal vent to avoid sagging and kinking that may result in  
reduced airflow and poor performance.  
Exhaust hood must be at least 12" (30.5 cm) from the ground or any object that may be in  
the path of the exhaust (such as flowers, rocks or bushes, snow line, etc.).  
Do not install flexible metal vent in enclosed walls, ceilings or floors.  
Do not use an exhaust hood with a magnetic latch.  
Elbows  
45° elbows provide better airflow than 90° elbows.  
Improper venting can cause moisture and lint to collect  
indoors, which may result in:  
Moisture damage to woodwork, furniture, paint, wallpaper,  
carpets, etc.  
Housecleaning problems and health problems.  
Good  
Better  
9
 
Plan Vent System  
Choose your exhaust installation type  
Recommended exhaust installations  
Typical installations vent the dryer from the rear of the dryer. Other installations are possible.  
B
A
B
C
C
D
A. Standard rear offset exhaust installation  
B. Left or right side exhaust installation  
C. Bottom exhaust installation  
E
F
A
Alternate installations for close clearances  
Venting systems come in many varieties. Select the type best for your installation. Two close-  
clearance installations are shown. Refer to the manufacturer’s instructions.  
G
B
H
A. Dryer  
B. Elbow  
C. Wall  
E. Clamps  
F. Rigid metal or flexible metal vent  
G. Vent length necessary to connect elbows  
H. Exhaust outlet  
D. Exhaust hood  
Optional exhaust installations  
This dryer can be converted to exhaust out the right side, left side, or through the bottom. If  
you prefer, you may contact your local dealer to have the dryer converted.  
A
B
A. Over-the-top installation (also available with one offset elbow)  
B. Periscope installation  
NOTE: The following kits for close clearance alternate installations are available for purchase.  
WARNING  
To order, please see the “Assistance or Service” section.  
Over-the-Top Installation:  
Part Number 4396028  
Periscope Installation (For use with dryer vent to wall vent mismatch):  
Part Number 4396037 - 0" (0 cm) to 18" (45.72 cm) mismatch  
Part Number 4396011 - 18" (45.72 cm) to 29" (73.66 cm) mismatch  
Part Number 4396014 - 29" (73.66 cm) to 50" (127 cm) mismatch  
Fire Hazard  
Cover unused exhaust holes with the following kit:  
279818 (white)  
Contact your local dealer.  
Failure to follow these instructions can result in death,  
fire, electrical shock, or serious injury.  
10  
 
Special provisions for mobile home installations  
Vent system chart  
The exhaust vent must be securely fastened to a noncombustible portion of the mobile home  
structure and must not terminate beneath the mobile home. Terminate the exhaust vent  
outside.  
NOTE: Side and bottom exhaust installations have a 90º turn inside the dryer. To determine  
maximum exhaust length, add one 90º turn to the chart.  
Number of  
90º turns  
or elbows  
Type of  
vent  
Box or  
louvered  
hoods  
Angled  
hoods  
0
1
2
3
4
Rigid metal  
64 ft (20 m)  
36 ft (11 m)  
58 ft (17.7 m)  
28 ft (8.5 m)  
Flexible metal  
Rigid metal  
Flexible metal  
54 ft (16.5 m)  
31 ft (9.4 m)  
48 ft (14.6 m)  
23 ft (7 m)  
Rigid metal  
Flexible metal  
44 ft (13.4 m)  
27 ft (8.2 m)  
38 ft (11.6 m)  
19 ft (5.8 m)  
Rigid metal  
Flexible metal  
35 ft (10.7 m)  
25 ft (7.6 m)  
29 ft (8.8 m)  
17 ft (5.2 m)  
Rigid metal  
Flexible metal  
27 ft (8.2 m)  
23 ft (7 m)  
21 ft (6.4 m)  
15 ft (4.6 m)  
Determine vent path  
Select the route that will provide the straightest and most direct path outdoors.  
Plan the installation to use the fewest number of elbows and turns.  
When using elbows or making turns, allow as much room as possible.  
Bend vent gradually to avoid kinking.  
Install Vent System  
1. Install exhaust hood. Use caulking compound to seal exterior wall opening around  
exhaust hood.  
2. Connect vent to exhaust hood. Vent must fit inside exhaust hood. Secure vent to exhaust  
hood with 4" (10.2 cm) clamp.  
Use the fewest 90° turns possible.  
3. Run vent to dryer location. Use the straightest path possible. See “Determine vent path” in  
“Plan Vent System.” Avoid 90º turns. Use clamps to seal all joints. Do not use duct tape,  
screws or other fastening devices that extend into the interior of the vent to secure vent.  
Determine vent length and elbows needed for best drying performance  
Use the Vent system chart below to determine type of vent material and hood  
combinations acceptable to use.  
Install Leveling Legs  
NOTE: Do not use vent runs longer than those specified in the Vent system chart. Exhaust  
systems longer than those specified will:  
WARNING  
Shorten the life of the dryer.  
Excessive Weight Hazard  
Reduce performance, resulting in longer drying times and increased energy usage.  
Use two or more people to move and install dryer.  
Failure to do so can result in back or other injury.  
The Vent system chart provides venting requirements that will help to achieve the best drying  
performance.  
1. To protect the floor, use a large flat piece of cardboard from the dryer carton. Place  
cardboard under the entire back edge of the dryer.  
11  
 
2. Firmly grasp the body of the dryer (not the top or console panel). Gently lay the dryer on  
A combination of pipe fittings must be used to connect the dryer to the existing gas line.  
Shown is a recommended connection. Your connection may be different, according to the  
supply line type, size and location.  
the cardboard. See illustration.  
D
3. Examine the leveling legs. Find the diamond marking.  
A
B
C
4. Screw the legs into the leg holes by hand. Use a wrench to finish turning the legs until the  
A. ³⁄₈" flexible gas connector  
B. ³⁄₈" dryer pipe  
diamond marking is no longer visible.  
5. Place a carton corner post from dryer packaging under each of the 2 dryer back corners.  
Stand the dryer up. Slide the dryer on the corner posts until it is close to its final location.  
Leave enough room to connect the exhaust vent or gas line.  
C. ³⁄₈" to ³⁄₈" pipe elbow  
D. ³⁄₈" pipe-to-flare adapter fitting  
3. Open the shutoff valve in the supply line. The valve is open when the handle is parallel to  
the gas pipe.  
For mobile home use  
Gas dryers must be securely fastened to the floor.  
A
B
A. Closed valve  
B. Open valve  
4. Test all connections by brushing on an approved noncorrosive leak-detection solution.  
Bubbles will show a leak. Correct any leak found.  
Mobile home installations require a Mobile Home Installation Kit. See “Tools and Parts”  
section for information on ordering.  
Connect Vent  
1. Using a 4" (10.2 cm) clamp, connect vent to exhaust outlet in dryer. If connecting to  
existing vent, make sure the vent is clean. The dryer vent must fit over the dryer exhaust  
outlet and inside the exhaust hood. Check that the vent is secured to exhaust hood with a  
4" (10.2 cm) clamp.  
2. Move dryer into its final location. Do not crush or kink vent.  
3. (On gas models) Check that there are no kinks in the flexible gas line.  
4. Once the exhaust vent connection is made, remove the corner posts and cardboard.  
Make Gas Connection  
1. Remove the red cap from the gas pipe.  
2. Using a wrench to tighten, connect the gas supply to the dryer. Use pipe-joint compound  
on the threads of all non-flared male fittings. If flexible metal tubing is used, be sure there  
are no kinks.  
Level Dryer  
A
B
Check the levelness of the dryer. Check levelness first side to side, then front to back.  
A. Flared male fitting  
B. Non-flared male fitting  
NOTE: For LP gas connections, you must use pipe-joint compound resistant to the action  
of LP gas. Do not use TEFLON®† tape.  
If the dryer is not level, prop up the dryer using a wood block. Use a wrench to adjust the legs  
up or down and check again for levelness.  
®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.  
12  
 
Complete Installation  
1. Check that all parts are now installed. If there is an extra part, go back through the steps to  
6. Remove any protective film on the console and any tape remaining on the dryer.  
7. Dispose of/recycle all packaging materials.  
8. Read “Dryer Use.”  
see which step was skipped.  
2. Check that you have all of your tools.  
3. Check the dryer’s final location. Be sure the vent is not crushed or kinked.  
4. Check that the dryer is level. See “Level Dryer.”  
9. Wipe the dryer drum interior thoroughly with a damp cloth to remove any dust.  
10. Select a Timed Dry heated cycle, and start the dryer. Do not select the Air Only  
Temperature setting.  
If the dryer will not start, check the following:  
WARNING  
Dryer is plugged into a grounded 3 prong outlet.  
Electrical supply is connected.  
Household fuse is intact and tight, or circuit breaker has not tripped.  
Dryer door is closed.  
11. When the dryer has been running for 5 minutes, open the dryer door and feel for heat. If  
you feel heat, cancel cycle and close door. If you do not feel heat, turn off the dryer and  
check that the gas supply line shutoff valve is open.  
Electrical Shock Hazard  
Plug into a grounded 3 prong outlet.  
Do not remove ground prong.  
Do not use an adapter.  
If the gas supply line shutoff valve is closed, open it, then repeat the 5-minute test as  
outlined above.  
If the gas supply line shutoff valve is open, contact a qualified technician.  
Do not use an extension cord.  
Failure to follow these instructions can result in death,  
fire, or electrical shock.  
5. Plug into a grounded 3 prong outlet. Turn on power.  
13  
 
DRYER USE  
Starting Your Dryer  
WARNING  
WARNING  
Explosion Hazard  
Fire Hazard  
Keep flammable materials and vapors, such as  
gasoline, away from dryer.  
No washer can completely remove oil.  
Do not dry anything that has ever had any type of oil on  
it (including cooking oils).  
Do not dry anything that has ever had anything  
flammable on it (even after washing).  
Items containing foam, rubber, or plastic must be dried  
on a clothesline or by using an Air Cycle.  
Failure to follow these instructions can result in death,  
explosion, or fire.  
Failure to follow these instructions can result in death  
or fire.  
This book covers several different models. Your dryer may not have all of the cycles and  
features described.  
8. Press the PUSH TO START button.  
Stopping and Restarting  
You can stop your dryer anytime during a cycle.  
Before using your dryer, wipe the dryer drum with a damp cloth to remove dust from storing  
and shipping.  
To stop your dryer  
1. Clean lint screen before each load. See “Cleaning the Lint Screen.”  
Open the dryer door or turn the Cycle Control knob to OFF.  
NOTE: The Cycle Control knob should point to an Off area when the dryer is not in use.  
To restart your dryer  
1. Close the door.  
2. Select a new cycle and temperature (if desired).  
3. Press the PUSH TO START button.  
2. Load clothes loosely into the dryer and close the door. Do not pack the dryer. Allow space  
for clothes to tumble freely.  
3. Turn the Cycle Control knob to the recommended cycle for the type of load being dried.  
ENERGY PREFERRED Sensor Dry setting is indicated on the timer dial, between the words  
MORE DRY and LESS DRY. Use this ENERGY PREFERRED cycle to dry most heavy- to  
medium-weight fabrics.  
4. Set the Temperature control to the recommended setting for the type of fabric being dried.  
See Dryer Cycle Descriptions (separate sheet) for temperature suggestions.  
How Sensor Dry Works  
5. (OPTIONAL) Your dryer may have a WRINKLE PREVENT feature selector. When you are  
unable to remove a load from the dryer as soon as it stops, wrinkles can form. This feature  
periodically tumbles, rearranges and fluffs the load without heat to help avoid wrinkling.  
When you are using the Sensor Dry Cycle, the dryness of the load is determined by two metal  
strips (sensors) located on the inside of the dryer. The metal strips help “feel” the amount of  
moisture left in the clothes as they tumble. When moisture is left in the clothes, the Cycle  
Control knob will not advance. As clothes begin to dry, the amount of water left in the clothes  
decreases, and the timer advances through the remainder of the cycle. When the selected  
dryness level is reached, the dryer goes into a cool down period of up to 10 minutes.  
6. (OPTIONAL) If you want the dryer to sound a signal when the cycle is finished, set the  
END OF CYCLE SIGNAL control to ON. The signal is helpful when you are drying  
permanent press, synthetics and other items that should be removed from the dryer as  
soon as it stops.  
7. If desired, add a fabric softener sheet. Follow package instructions.  
14  
 
Drying Rack  
DRYER CARE  
The drying rack is useful for machine drying items you would not necessarily want to tumble  
dry (for example, sweaters).  
If your model does not have a drying rack, you may be able to purchase one for your model.  
To find out whether your model allows drying rack usage and for information on ordering,  
please refer to the front page of the manual or contact the dealer from whom you purchased  
your dryer.  
Cleaning the Dryer Location  
Keep dryer area clear and free from items that would obstruct the flow of combustion and  
ventilation air.  
To use the drying rack  
WARNING  
1. Do not remove the lint screen.  
2. Slide drying rack over the bottom of the dryer door opening. Push down to secure rack on  
frame.  
Explosion Hazard  
Keep flammable materials and vapors, such as  
gasoline, away from dryer.  
3. Put the wet items on top of the rack. Leave space between the items so air can reach all  
the surfaces. Close the door.  
Place dryer at least 18 inches (46 cm) above the floor  
for a garage installation.  
NOTE: Do not allow items to hang over the edge of the rack.  
4. Select a timed drying cycle and temperature, or an air cycle. Items containing foam,  
Failure to do so can result in death, explosion, or fire.  
rubber, or plastic must be dried on a clothesline or by using an air cycle.  
5. Press the PUSH TO START button.  
NOTE: You must remove the drying rack for normal tumbling. Do not use Sensor Dry cycles  
Cleaning the Lint Screen  
Clean lint screen before each load. A screen blocked by lint can increase drying time.  
IMPORTANT:  
with the drying rack.  
This chart shows examples of items that can be rack dried and the suggested cycle,  
temperature setting and drying time. Actual drying time will depend on the amount of  
moisture items hold.  
Do not run the dryer with the lint screen loose, damaged, blocked or missing. Doing so  
can cause overheating and damage to both the dryer and fabrics.  
Rack Dry  
Cycle  
Temp  
Time*  
If lint falls off the screen into the dryer during removal, check the exhaust hood and  
remove the lint.  
Wool Sweaters  
Block to shape and lay flat on the rack  
Timed  
Low  
60  
Stuffed toys or pillows  
Timed  
Timed  
Timed  
Low  
60  
90  
90  
Every Load Cleaning  
Cotton or polyester fiber filled  
1. The lint screen is located in the door of the dryer. Pull the lint screen straight up. Roll lint  
off the screen with your fingers. Do not rinse or wash screen to remove lint. Wet lint is  
hard to remove.  
Stuffed toys or pillows  
Foam rubber filled  
Air  
(no heat)  
Sneakers or canvas shoes  
Air  
(no heat)  
*(Minutes) Reset time to complete drying, if needed.  
2. Push the lint screen firmly back into place.  
15  
 
As Needed Cleaning  
Vacation and Moving Care  
1. Roll lint off the screen with your fingers.  
2. Wet both sides of lint screen with hot water.  
Vacation care  
3. Wet a nylon brush with hot water and liquid detergent. Scrub lint screen with the brush to  
Operate your dryer only when you are at home. If you will be on vacation or not using your  
dryer for an extended period of time, you should:  
remove residue buildup.  
4. Rinse screen with hot water.  
1. Unplug dryer or disconnect power.  
5. Thoroughly dry lint screen with a clean towel. Replace screen in dryer.  
2. Close shutoff valve in gas supply line.  
3. Clean lint screen. See “Cleaning the Lint Screen.”  
Cleaning the Dryer Interior  
Moving care  
1. Apply a liquid, nonflammable household cleaner to the stained area of the drum and rub  
with a soft cloth until stain is removed.  
1. Unplug the power supply cord.  
2. Wipe drum thoroughly with a damp cloth.  
2. Close shutoff valve in gas supply line.  
3. Disconnect gas supply line pipe and remove fittings attached to dryer pipe.  
4. Cap the open fuel supply line.  
3. Tumble a load of clean cloths or towels to dry the drum.  
NOTE: Garments that contain unstable dyes, such as denim blue jeans or brightly colored  
cotton items, may discolor the dryer interior. These stains are not harmful to your dryer and  
will not stain future loads of clothes. Dry unstable dye items inside-out to avoid transfer of  
dye.  
5. Make sure leveling legs are secure in dryer base.  
6. Use masking tape to secure dryer door.  
Removing Accumulated Lint  
From Inside the Dryer Cabinet  
Lint should be removed every 2 years, or more often, depending on dryer usage. Cleaning  
should be done by a qualified person.  
Changing the Drum Light  
1. Unplug dryer or disconnect power.  
2. Open the dryer door. Locate the light bulb cover on the back wall of the dryer. Remove  
the screw located in the lower right-hand corner of the cover. Remove the cover.  
From the Exhaust Vent  
Lint should be removed every 2 years, or more often, depending on dryer usage.  
3. Turn bulb counterclockwise. Replace the bulb with a 10-watt appliance bulb only.  
Replace the cover and secure with the screw.  
4. Plug in dryer or reconnect power.  
16  
 
TROUBLESHOOTING  
First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions) to possibly avoid the cost of a service call...  
Timer does not noticeably advance  
Dryer Operation  
Is the dryer set to Timed Dry?  
The timer moves slowly and continuously for the time setting.  
Dryer will not run  
Is the dryer set to Sensor Dry?  
The timer moves only when the clothing is mostly dry. See “How Sensor Dry Works” in  
“Dryer Use.”  
Has a household fuse blown, or has a circuit breaker tripped?  
Replace the fuse or reset the circuit breaker. If the problem continues, call an electrician.  
Was a regular fuse used?  
Use a time-delay fuse.  
Dryer Results  
Is the dryer door firmly closed?  
Was the Start button firmly pressed?  
Clothes are not drying satisfactorily, drying times are too long, or load is too hot  
Is a cycle selected?  
The dryer will not start in the Wrinkle Prevent position. Move the dial past OFF.  
Is the lint screen clogged with lint?  
Lint screen should be cleaned before each load.  
No heat  
WARNING  
Has a household fuse blown, or has a circuit breaker tripped?  
The drum may be turning, but you may not have heat. Replace the fuse or reset the circuit  
breaker. If the problem continues, call an electrician.  
Is the valve open on the gas supply line?  
Unusual sounds  
Fire Hazard  
Use a heavy metal vent.  
Has the dryer had a period of non-use?  
If the dryer hasn’t been used for a while, there may be a thumping sound during the first  
few minutes of operation.  
Do not use a plastic vent.  
Do not use a metal foil vent.  
Is a coin, button, or paper clip caught between the drum and front or rear of the dryer?  
Check the front and rear edges of the drum for small objects. Clean out pockets before  
laundering.  
Failure to follow these instructions can result in death  
or fire.  
Is it a gas dryer?  
The gas valve clicking is a normal operating sound.  
Is the exhaust vent or outside exhaust hood clogged with lint, restricting air movement?  
Run the dryer for 5-10 minutes. Hold your hand under the outside exhaust hood to check  
air movement. If you do not feel air movement, clean exhaust system of lint or replace  
exhaust vent with heavy metal or flexible metal vent. See the Installation Instructions.  
Are the four legs installed, and is the dryer level front to back and side to side?  
The dryer may vibrate if not properly installed. See the Installation Instructions.  
Is the clothing knotted or balled up?  
When balled up, the load will bounce, causing the dryer to vibrate. Separate the load  
items and restart the dryer.  
Are fabric softener sheets blocking the grille?  
Use only one fabric softener sheet, and use it only once.  
Is the exhaust vent the correct length?  
Check that the exhaust vent is not too long or has too many turns. Long venting will  
increase drying times. See the Installation Instructions.  
17  
 
Is the exhaust vent diameter the correct size?  
Use 4" (10.2 cm) diameter vent material.  
Cycle time too short  
WARNING  
WARNING  
Excessive Weight Hazard  
Use two or more people to move and install dryer.  
Failure to do so can result in back or other injury.  
Explosion Hazard  
Is the Sensor Dry cycle ending early?  
Keep flammable materials and vapors, such as  
gasoline, away from dryer.  
The load may not be contacting the sensor strips. Level the dryer.  
Change the dryness level setting on Sensor Dry cycles. Increasing or decreasing the  
dryness level will change the amount of drying time in a cycle.  
Place dryer at least 18 inches (46 cm) above the floor  
for a garage installation.  
Lint on load  
Failure to do so can result in death, explosion, or fire.  
Is the lint screen clogged?  
Lint screen should be cleaned before each load.  
Is the dryer located in a room with temperature below 45ºF (7ºC)?  
Proper operation of dryer cycles requires temperatures above 45ºF (7ºC).  
Stains on load or drum  
Is the dryer located in a closet?  
Closet doors must have ventilation openings at the top and bottom of the door. Sides and  
front of dryer require a minimum of 1" (2.5 cm) of airspace, and the rear of the dryer  
requires 5" (12.7 cm). See the Installation Instructions.  
Was dryer fabric softener properly used?  
Add dryer fabric softener sheets at the beginning of the cycle. Fabric softener sheets added  
to a partially dried load can stain your garments.  
Has an air dry cycle been selected?  
Select the right cycle for the types of garments being dried.  
Drum stains are caused by dyes in clothing (usually blue jeans). This will not transfer to  
other clothing.  
Is the load too large and heavy to dry quickly?  
Separate the load to tumble freely.  
Loads are wrinkled  
Was the load removed from dryer at the end of the cycle?  
Was the dryer overloaded?  
Dry smaller loads that can tumble freely.  
Odors  
Have you recently been painting, staining or varnishing in the area where your dryer is  
located?  
If so, ventilate the area. When the odors or fumes are gone from the area, rewash and dry  
the clothing.  
18  
 
ASSISTANCE OR SERVICE  
ACCESSORIES  
Enhance your dryer with these premium accessories.  
For more high-quality items or to order, call 1-800-901-2042, or visit us at  
Before calling for assistance or service, please check “Troubleshooting.” It may save you the  
cost of a service call. If you still need help, follow the instructions below.  
When calling, please know the purchase date and the complete model and serial number of  
your appliance. This information will help us to better respond to your request.  
Part Number  
20-48KITRC  
PT220L  
PT400L  
PT600L  
8212614  
31682  
1903WH  
3404351  
Accessory  
4" (10.2 cm) gas line dryer connector installation kit  
4" (10.2 cm) dryer cord, 3-wire, 30 amp  
4" (10.2 cm) dryer cord, 4-wire, 30 amp  
6" (15.2 cm) dryer cord, 4-wire, 30 amp  
Dryer vent lint brush  
All-purpose appliance cleaner  
Laundry supply storage cart  
Drying rack - fits 29" (73.7 cm) Super Capacity, 6.5 cu. ft (0.20 cu. m) -  
side swing or hamper door  
If you need replacement parts  
If you need to order replacement parts, we recommend that you use only factory specified  
parts. Factory specified parts will fit right and work right because they are made with the same  
precision used to build every new MAYTAG® appliance.  
To locate factory specified parts in your area, call the following customer assistance telephone  
number or your nearest designated service center.  
In the U.S.A.  
Call Maytag Services, LLC Customer Assistance toll free: 1-800-688-9900, or vist our website  
3406839  
Drying rack - fits 29" (73.7 cm) Super Capacity Plus, 7.0 cu. ft (0.18 cu. m)  
- side swing door only  
Our consultants provide assistance with:  
8212450  
49971  
Drying rack - fits 27" (68.6 cm) Ultra Capacity - side swing door only  
Compact dryer stand - white  
Features and specifications on our full line of appliances.  
Installation information.  
49572  
LP gas conversion kit  
Use and maintenance procedures.  
Accessory and repair parts sales.  
Specialized customer assistance (Spanish speaking, hearing impaired, limited vision,  
etc.).  
Referrals to local dealers, repair parts distributors and service companies. Maytag®  
appliances designated service technicians are trained to fulfill the product warranty and  
provide after-warranty service, anywhere in the United States.  
To locate the Maytag® appliances designated service company in your area, you can also  
look in your telephone directory Yellow Pages.  
For further assistance  
If you need further assistance, you can write to Maytag® appliances with any questions or  
concerns at:  
Maytag Services, LLC  
ATTN: CAIR® Center  
P.O. Box 2370  
Cleveland, TN 37320-2370  
Please include a daytime phone number in your correspondence.  
19  
 
MAYTAG CORPORATION MAJOR APPLIANCE WARRANTY  
ONE YEAR LIMITED WARRANTY  
For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or furnished with the product, Maytag Corporation or  
Maytag Limited (hereafter “Maytag”) will pay for Factory Specified Parts and repair labor to correct defects in materials or workmanship. Service must be provided by a Maytag designated  
service company. This limited warranty applies only when the major appliance is used in the country in which it was purchased.  
ITEMS MAYTAG WILL NOT PAY FOR  
1. Service calls to correct the installation of your major appliance, to instruct you how to use your major appliance, to replace or repair house fuses or to correct house wiring or plumbing.  
2. Service calls to repair or replace appliance light bulbs, air filters or water filters. Those consumable parts are excluded from warranty coverage.  
3. Repairs when your major appliance is used for other than normal, single-family household use.  
4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in accordance with electrical or plumbing codes, or use of  
products not approved by Maytag.  
5. Any food loss due to refrigerator or freezer product failures.  
6. Replacement parts or repair labor costs for units operated outside the United States or Canada.  
7. Pickup and delivery. This major appliance is designed to be repaired in the home.  
8. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.  
9. Expenses for travel and transportation for product service in remote locations.  
10. The removal and reinstallation of your appliance if it is installed in an inaccessible location or is not installed in accordance with published installation instructions.  
11. Replacement parts or repair labor costs when the major appliance is used in a country other than the country in which it was purchased.  
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES  
CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. IMPLIED WARRANTIES, INCLUDING  
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. MAYTAG SHALL  
NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR  
CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY  
NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE OR PROVINCE TO  
PROVINCE.  
Outside the 50 United States and Canada, this warranty does not apply. Contact your authorized Maytag dealer to determine if another warranty applies.  
If you need service, first see the “Troubleshooting” section of the Use & Care Guide. After checking “Troubleshooting,” additional help can be found by checking the “Assistance or Service”  
section or by calling Maytag. In the U.S.A., call 1-800-688-9900. In Canada, call 1-800-807-6777.  
9/06  
Keep this book and your sales slip together for future reference. You must provide  
Dealer name _____________________________________________________________________________  
proof of purchase or installation date for in-warranty service.  
Address _________________________________________________________________________________  
Write down the following information about your major appliance to better help you obtain  
assistance or service if you ever need it. You will need to know your complete model  
number and serial number. You can find this information on the model and serial number  
label located on the product.  
Phone number ___________________________________________________________________________  
Model number ___________________________________________________________________________  
Serial number ____________________________________________________________________________  
Purchase date ___________________________________________________________________________  
W10155111A  
SP PN W10155112A  
© 2007  
8/07  
Printed in U.S.A.  
All rights reserved.  
®Registered Trademark/ ™ Trademark of Maytag Corporation or its related companies.  
 

Lenovo Laptop 2491 User Manual
Lenovo Laptop N580 User Manual
LG Electronics Portable DVD Player DP771 User Manual
Liebert Clothes Dryer 1010 User Manual
Link electronic Network Router 8x8 HD SDI User Manual
Lucent Technologies Network Card VPN Firewall Brick 20 User Manual
Makita eBook Reader DC07SA User Manual
Master Bilt Electric Grill 20150112 User Manual
MasterCraft Chainsaw 100524 01 CS 120CB User Manual
Maytag Clothes Dryer W10267633A User Manual