Makita Cordless Saw 5620D User Manual

Cordless Circular Saw  
Equipped with Electric Blade Brake  
165 mm (6-1/2”)  
MODEL 5620D  
001320  
I N S T R U C T I O N M A N U A L  
WARNING:  
For your personal safety, READ and UNDERSTAND before using.  
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.  
 
able for one type of battery may create a risk  
of fire when used with another battery.  
13. Do not force tool. Use the correct tool for  
your application. The correct tool will do the  
job better and safer at the rate for which it is  
designed.  
5. Use battery operated tool only with specif-  
ically designated battery pack. Use of any  
other batteries may create a risk of fire.  
14. Do not use tool if switch does not turn it  
on or off. A tool that cannot be controlled  
with the switch is dangerous and must be  
repaired.  
Personal Safety  
6. Stay alert, watch what you are doing, and  
use common sense when operating a  
power tool. Do not use tool while tired or  
under the influence of drugs, alcohol, or  
medication. A moment of inattention while  
operating power tools may result in serious  
personal injury.  
15. Disconnect battery pack from tool or  
place the switch in the locked or off posi-  
tion before making any adjustments,  
changing accessories, or storing the tool.  
Such preventive safety measures reduce the  
risk of starting the tool accidentally.  
7. Dress properly. Do not wear loose cloth-  
ing or jewelry. Contain long hair. Keep  
your hair, clothing, and gloves away from  
moving parts. Loose clothes, jewelry, or long  
hair can be caught in moving parts.  
16. Store idle tools out of reach of children  
and other untrained persons. Tools are  
dangerous in the hands of untrained users.  
17. When battery pack is not in use, keep it  
away from other metal objects like: paper  
clips, coins, keys, nails, screws, or other  
small metal objects that can make a con-  
nection from one terminal to another.  
Shorting the battery terminals together may  
cause sparks, burns, or a fire.  
8. Avoid accidental starting. Be sure switch  
is in the locked or off position before  
inserting battery pack. Carrying tools with  
your finger on the switch or inserting the bat-  
tery pack into a tool with the switch on invites  
accidents.  
18. Maintain tools with care. Keep cutting  
tools sharp and clean. Properly maintained  
tools with sharp cutting edge are less likely to  
bind and are easier to control.  
9. Remove adjusting keys or wrenches  
before turning the tool on. A wrench or a  
key that is left attached to a rotating part of  
the tool may result in personal injury.  
19. Check for misalignment or binding of  
moving parts, breakage of parts, and any  
other condition that may affect the tool’s  
operation. If damaged, have the tool ser-  
viced before using. Many accidents are  
caused by poorly maintained tools.  
10. Do not overreach. Keep proper footing  
and balance at all times. Proper footing and  
balance enable better control of the tool in  
unexpected situations.  
11. Use safety equipment. Always wear eye  
protection. Dust mask, non-skid safety  
shoes, hard hat, or hearing protection must  
be used for appropriate conditions.  
20. Use only accessories that are recom-  
mended by the manufacturer for your  
model. Accessories that may be suitable for  
one tool may create a risk of injury when  
used on another tool.  
Tool Use and Care  
12. Use clamps or other practical way to  
secure and support the workpiece to a  
stable platform. Holding the work by hand or  
against your body is unstable and may lead  
to loss of control.  
SERVICE  
21. Tool service must be performed only by  
qualified repair personnel. Service or main-  
tenance performed by unqualified personnel  
may result in a risk of injury.  
3
 
22. When servicing a tool, use only identical  
replacement parts. Follow instructions in  
the Maintenance section of this manual.  
Use of unauthorized parts or failure to follow  
Maintenance instructions may create a risk of  
shock or injury.  
SPECIFIC SAFETY RULES  
USB067-1  
DO NOT let comfort or familiarity with product (gained from  
repeated use) replace strict adherence to circular saw safety  
rules. If you use this tool unsafely or incorrectly, you can suffer  
serious personal injury.  
1. DANGER! Keep hands away from cutting  
area and blade. Keep your second hand  
on auxiliary handle or motor housing. If  
both hands are holding the saw, they cannot  
be cut by the blade.  
3. Check the operation and condition of the  
lower guard spring. If the guard and the  
spring are not operating properly, they  
must be serviced before use. Lower guard  
may operate sluggishly due to damaged  
parts, gummy deposits, or a buildup of debris.  
Keep your body positioned to either side  
of the saw blade, but not in line with the  
saw blade. KICKBACK could cause the saw  
to jump backwards. (See “Causes and Oper-  
ator Prevention of Kickback”)  
Do not reach underneath the work. The  
guard can not protect you from the blade  
below the work. Do not attempt to remove cut  
material when blade is moving.  
4. Lower guard should be retracted manually  
only for special cuts such as “Pocket  
Cuts” and “Compound Cuts.Raise lower  
guard by Retracting Lever. As soon as  
blade enters the material, lower guard  
must be released. For all other sawing, the  
lower guard should operate automatically.  
CAUTION: Blades coast after turn off. Wait  
until blade stops before grasping cut material.  
5. Always observe that the lower guard is  
covering the blade before placing saw  
down on bench or floor. An unprotected,  
coasting blade will cause the saw to walk  
backwards, cutting whatever is in its path. Be  
aware of the time it takes for the blade to stop  
after switch is released.  
2. Check lower guard for proper closing  
before each use. Do not operate saw if  
lower guard does not move freely and  
close instantly. Never clamp or tie the  
lower guard into the open position. If saw  
is accidentally dropped, lower guard may be  
bent. Raise the lower guard with the Retract-  
ing Lever and make sure it moves freely and  
does not touch the blade or any other part, in  
all angles and depths of cut.  
6. NEVER hold piece being cut in your hands  
or across your leg. It is important to support  
the work properly to minimize body exposure,  
blade binding, or loss of control.  
7. Hold tool by insulated gripping surfaces  
when performing an operation where the  
cutting tool may contact hidden wiring.  
Contact with a “live” wire will also make  
exposed metal parts of the tool “live” and  
shock the operator.  
To check lower guard, open lower guard by  
hand, then release and watch guard closure.  
Also check to see that Retracting Lever does  
not touch tool housing. Leaving blade  
exposed is VERY DANGEROUS and can  
lead to serious personal injury.  
4
 
8. When ripping always use a rip fence or  
straight edge guide. This improves the  
accuracy of cut and reduces the chance for  
blade binding.  
corrective actions to eliminate the cause of  
blade binding.  
When restarting a saw in the workpiece,  
center the saw blade in the kerf and check  
that teeth are not engaged into the mate-  
rial. If saw blade is binding, it may walk up or  
KICKBACK from the workpiece as the saw is  
restarted.  
Support large panels to minimize the risk  
of blade pinching and KICKBACK. Large  
panels tend to sag under their own weight.  
Supports must be placed under the panel on  
both sides, near the line of cut and near the  
edge of the panel as shown in Fig. 1.  
To minimize the risk of blade pinching and  
kickback. When cutting operation requires  
the resting of the saw on the workpiece, the  
saw shall be rested on the larger portion and  
the smaller piece cut off.  
9. Always use blades with correct size and  
shape (diamond vs. round) arbor holes.  
Blades that do not match the mounting hard-  
ware of the saw will run eccentrically, causing  
loss of control.  
10. Never use damaged or incorrect blade  
washers or bolts. The blade washers and  
bolt were specially designed for your saw, for  
optimum performance and safety of opera-  
tion.  
11. Causes and Operator Prevention of Kick-  
back:  
Kickback is a sudden reaction to a pinched,  
bound, or misaligned saw blade, causing an  
uncontrolled saw to lift up and out of the  
workpiece toward the operator.  
When the blade is pinched or bound tightly by  
the kerf closing down, the blade stalls and the  
motor reaction drives the unit rapidly back  
toward the operator.  
If the blade becomes twisted or misaligned in  
the cut, the teeth at the back edge of the  
blade can dig into the top surface of the wood  
causing the blade to climb out of the kerf and  
jump back toward the operator.  
Fig. 1  
Kickback is the result of tool misuse and/or  
incorrect operating procedures or conditions  
and can be avoided by taking proper precau-  
tions as given below:  
Maintain a firm grip on the saw and posi-  
tion your body and arm in a way that  
allows you to resist KICKBACK forces.  
KICKBACK forces can be controlled by the  
operator, if proper precautions are taken.  
When blade is binding, or when interrupt-  
ing a cut for any reason, release the trig-  
ger and hold the saw motionless in the  
material until the blade comes to a com-  
plete stop. Never attempt to remove the  
saw from the work or pull the saw back-  
ward while the blade is in motion or KICK-  
BACK may occur. Investigate and take  
Fig. 2  
Do not use dull or damaged blade.  
Unsharpened or improperly set blades pro-  
duce narrow kerf causing excessive friction,  
blade binding and KICKBACK. Keep blade  
sharp and clean. Gum and wood pitch hard-  
ened on blades slows saw and increases  
potential for kickback. Keep blade clean by  
first removing it from tool, then cleaning it  
with gum and pitch remover, hot water or ker-  
osene. Never use gasoline.  
5
 
Blade depth and bevel adjusting locking  
levers must be tight and secure before  
making cut. If blade adjustment shifts while  
cutting, it will cause binding and KICKBACK.  
Use extra caution when making a “Pocket  
Cut” into existing walls or other blind  
areas. The protruding blade may cut objects  
that can cause KICKBACK. For pocket cuts,  
retract lower guard using Retracting Lever.  
ALWAYS hold the tool firmly with both  
hands. NEVER place your hand or fingers  
behind the saw. If kickback occurs, the saw  
could easily jump backwards over your hand,  
leading to serious personal injury.  
workpiece support.  
WARNING: It is important to support the  
workpiece properly and to hold the saw  
firmly to prevent loss of control which  
could cause personal injury. Fig. 4 illus-  
trates typical hand support of the saw.  
Fig. 4  
17. Place the wider portion of the saw base on  
that part of the workpiece which is solidly  
supported, not on the section that will fall  
off when the cut is made. As examples,  
Fig. 5 illustrates the RIGHT way to cut off  
the end of a board, and Fig. 6 the WRONG  
way. If the workpiece is short or small,  
clamp it down. DO NOT TRY TO HOLD  
SHORT PIECES BY HAND!  
Fig. 3  
Never force the saw. Forcing the saw can  
cause uneven cuts, loss of accuracy, and  
possible kickback.  
Push the saw forward at a speed so that the  
blade cuts without slowing.  
12. Be aware that this tool is always in an  
operating condition, because it does not  
have to be plugged into an electrical out-  
let.  
13. Use extra caution when cutting damp  
wood, pressure treated lumber, or wood  
containing knots. Adjust speed of cut to  
maintain smooth advancement of tool without  
decrease in blade speed.  
Fig. 5  
14. Adjustments. Before cutting be sure  
depth and bevel adjustments are tight.  
15. Avoid Cutting Nails. Inspect for and  
remove all nails from lumber before cut-  
ting.  
Fig. 6  
18. Never attempt to saw with the circular saw  
16. The tool is provided with a front grip and  
rear handle for two hand operation. Oper-  
ate with proper hand support and proper  
held upside down in  
a
vise. This is  
6
 
extremely dangerous and can lead to seri-  
ous accidents.  
19. WARNING: Blade coasts to stop after  
switch is released. Contact with coasting  
blade can cause serious injury. Before  
setting the tool down after completing a  
cut, be sure that the lower (telescoping)  
guard has closed and the blade has come  
to a complete stop.  
20. Some material contains chemicals which  
may be toxic. Take caution to prevent dust  
inhalation and skin contact. Follow mate-  
rial supplier safety data.  
Fig. 7  
SAVE THESE INSTRUCTIONS  
WARNING:  
MISUSE or failure to follow the safety rules stated in this  
instruction manual may cause serious personal injury.  
SYMBOLS  
USD301-1  
The followings show the symbols used for tool.  
V .......................volts  
....................no load speed  
n
˚
...................direct current  
.../min................revolutions or reciprocation per  
minute  
IMPORTANT SAFETY INSTRUCTIONS FOR  
BATTERY CARTRIDGE  
ENC004-1  
1. Before using battery cartridge, read all  
instructions and cautionary markings on  
(1) battery charger, (2) battery, and (3)  
product using battery.  
2. Do not disassemble battery cartridge.  
3. If operating time has become excessively  
shorter, stop operating immediately. It  
7
 
may result in a risk of overheating, possi-  
ble burns and even an explosion.  
(3) Do not expose battery cartridge to  
water or rain.  
4. If electrolyte gets into your eyes, rinse  
them out with clear water and seek medi-  
cal attention right away. It may result in  
loss of your eyesight.  
A battery short can cause a large current  
flow, overheating, possible burns and  
even a breakdown.  
7. Do not store the tool and battery cartridge  
in locations where the temperature may  
reach or exceed 50°C (122°F).  
5. Always cover the battery terminals with  
the battery cover when the battery car-  
tridge is not used.  
8. Do not incinerate the battery cartridge  
even if it is severely damaged or is com-  
pletely worn out. The battery cartridge can  
explode in a fire.  
6. Do not short the battery cartridge:  
(1) Do not touch the terminals with any  
conductive material.  
9. Be careful not to drop or strike battery.  
(2) Avoid storing battery cartridge in a  
container with other metal objects  
such as nails, coins, etc.  
SAVE THESE INSTRUCTIONS  
Tips for maintaining maximum battery life  
1. Charge the battery cartridge before com-  
pletely discharged.  
3. Charge the battery cartridge with room  
temperature at 10°C - 40°C (50°F - 104°F).  
Let a hot battery cartridge cool down  
before charging it.  
Always stop tool operation and charge the  
battery cartridge when you notice less  
tool power.  
4. Charge the Nickel Metal Hydride battery  
cartridge when you do not use it for more  
than six months.  
2. Never recharge a fully charged battery  
cartridge.  
Overcharging shortens the battery service  
life.  
8
 
FUNCTIONAL  
DESCRIPTION  
CAUTION:  
Always be sure that the tool is switched off and the  
battery cartridge is removed before adjusting or  
checking function on the tool.  
001328  
Installing or removing battery cartridge  
Always switch off the tool before insertion or removal of  
the battery cartridge.  
1
To remove the battery cartridge, withdraw it from the tool  
while pressing the buttons on both sides of the cartridge.  
To insert the battery cartridge, align the tongue on the  
battery cartridge with the groove in the housing and slip  
it into place. Always insert it all the way until it locks in  
place with a little click. If not, it may accidentally fall out  
of the tool, causing injury to you or someone around you.  
2
1. Battery cartridge  
2. Button  
Do not use force when inserting the battery cartridge. If  
the cartridge does not slide in easily, it is not being  
inserted correctly.  
001351  
Adjusting depth of cut  
CAUTION:  
After adjusting the depth of cut, always tighten the lever  
securely.  
Loosen the lever on the side of the rear handle and move the  
base up or down. At the desired depth of cut, secure the  
base by tightening the lever.  
1
1. Lever  
For cleaner, safer cuts, set cut depth so that no more than  
one blade tooth projects below workpiece. Using proper cut  
depth helps to reduce potential for dangerous KICKBACKS  
which can cause personal injury.  
001368  
Bevel cutting  
Loosen the clamping screw on the bevel scale plate on the  
front of the base. Set for the desired angle (0° - 50°) by tilting  
accordingly, then tighten the clamping screw securely.  
2
1
1. Clamping screw  
2. Bevel scale plate  
9
 
001386  
Sighting  
For straight cuts, align the A position on the front of the base  
with your cutting line. For 45° bevel cuts, align the B position  
with it.  
1
B
A
2
1. Base  
2. Cutting line  
001407  
Switch action  
CAUTION:  
1
2
Before inserting the battery cartridge into the tool,  
always check to see that the switch trigger actuates  
properly and returns to the OFFposition when  
released.  
To prevent the switch trigger from being accidentally pulled, a  
lock-off button is provided. To start the tool, push in the lock-  
off button and pull the switch trigger. Release the switch trig-  
ger to stop.  
1. Lock-off button  
2. Switch trigger  
Electric brake  
This tool is equipped with an electric blade brake. If the tool  
consistently fails to quickly stop blade after switch trigger  
release, have tool serviced at a Makita service center.  
The blade brake system is not a substitute for lower guard.  
NEVER USE TOOL WITHOUT A FUNCTIONING LOWER  
GUARD. SERIOUS PERSONAL INJURY CAN RESULT.  
10  
 
ASSEMBLY  
CAUTION:  
Always be sure that the tool is switched off and the  
battery cartridge is removed before carrying out any  
work on the tool.  
001428  
Removing or installing saw blade  
CAUTION:  
Be sure the blade is installed with teeth pointing up at  
the front of the tool.  
1
2
Use only the Makita wrench to install or remove the  
blade.  
1. Shaft lock  
To remove the blade, press the shaft lock so that the blade  
cannot revolve and use the wrench to loosen the hex bolt  
clockwise. Then remove the hex bolt, outer flange and blade.  
2. Hex wrench  
001445  
To install the blade, follow the removal procedure in reverse.  
BE SURE TO TIGHTEN THE HEX BOLT COUNTER-  
CLOCKWISE SECURELY.  
1
When changing blade, make sure to also clean upper and  
lower blade guards of accumulated sawdust. Such efforts do  
not, however, replace the need to check lower guard opera-  
tion before each use.  
4
2
3
1. Saw blade  
2. Hex bolt  
3. Outer flange  
4. Inner flange  
001453  
Hex wrench storage  
When not in use, store the hex wrench as shown in the figure  
to keep it from being lost.  
1
1. Hex wrench  
11  
 
OPERATION  
CAUTION:  
Be sure to move the tool forward in a straight line gently.  
Forcing or twisting the tool will result in overheating the  
motor and dangerous kickback, possibly causing severe  
injury.  
If the tool is operated continuously until the battery  
cartridge has discharged, allow the tool to rest for 15  
minutes before proceeding with a fresh battery.  
001471  
Hold the tool firmly. The tool is provided with both a front grip  
and rear handle. Use both to best grasp the tool. If both  
hands are holding saw, they cannot be cut by the blade. Set  
the base on the workpiece to be cut without the blade making  
any contact. Then turn the tool on and wait until the blade  
attains full speed. Now simply move the tool forward over the  
workpiece surface, keeping it flat and advancing smoothly  
until the sawing is completed.  
1
2
3
1. Rear handle  
2. Front grip  
3. Base  
To get clean cuts, keep your sawing line straight and your  
speed of advance uniform. If the cut fails to properly follow  
your intended cut line, do not attempt to turn or force the tool  
back to the cut line. Doing so may bind the blade and lead to  
dangerous kickback and possible serious injury. Release  
switch, wait for blade to stop and then withdraw tool. Realign  
tool on new cut line, and start cut again. Attempt to avoid  
positioning which exposes operator to chips and wood dust  
being ejected from saw. Use eye protection to help avoid  
injury.  
001490  
Rip fence (Guide rule)  
The handy rip fence allows you to do extra-accurate straight  
cuts. Simply slide the rip fence up snugly against the side of  
the workpiece and secure it in position with the screw on the  
front of the base. It also makes repeated cuts of uniform  
width possible.  
1
2
1. Clamp screw  
2. Rip fence (Guide rule)  
12  
 
MAINTENANCE  
CAUTION:  
Always be sure that the tool is switched off and the  
battery cartridge is removed before attempting to  
perform inspection or maintenance.  
001501  
Adjusting for accuracy of 90° cut (vertical cut)  
This adjustment has been made at the factory. But if it is off,  
adjust the adjusting screw with a hex wrench while squaring  
the blade with the base using a triangular rule, try square,  
etc.  
2
1
1. Adjusting screw  
2. Base  
001510  
1
1. Triangular rule  
001145  
Replacing carbon brushes  
Remove and check the carbon brushes regularly. Replace  
when they wear down to the limit mark. Keep the carbon  
brushes clean and free to slip in the holders. Both carbon  
brushes should be replaced at the same time. Use only iden-  
tical carbon brushes.  
1
1. Limit mark  
001524  
Use a screwdriver to remove the brush holder caps. Take out  
the worn carbon brushes, insert the new ones and secure  
the brush holder caps.  
1
2
After replacing brushes, insert the battery cartridge into the  
tool and break in brushes by running tool with no load for  
about 1 minute. Then check the tool while running and elec-  
tric brake operation when releasing the switch trigger. If elec-  
tric brake is not working well, ask your local Makita service  
center for repair.  
1. Brush holder cap  
2. Screwdriver  
13  
 
To maintain product SAFETY and RELIABILITY, repairs, any  
other maintenance or adjustment should be performed by  
Makita Authorized or Factory Service Centers, always using  
Makita replacement parts.  
EN0001-1  
Recycling the Battery  
The only way to dispose of a Makita battery is to recycle it.  
The law prohibits any other method of disposal.  
To recycle the battery:  
1. Remove the battery from the tool.  
Ni-Cd  
2. a) Take the battery to your nearest Makita Factory Ser-  
vice Center  
or  
b) Take the battery to your nearest Makita Authorized  
Service Center or Distributor that has been desig-  
nated as a Makita battery recycling location.  
Call your nearest Makita Service Center or Distributor to  
determine the location that provides Makita battery recycling.  
See your local Yellow Pages under “Tools-Electric”.  
ACCESSORIES  
CAUTION:  
These accessories or attachments are recommended for  
use with your Makita tool specified in this manual. The  
use of any other accessories or attachments might  
present a risk of injury to persons. Only use accessory  
or attachment for its stated purpose.  
If you need any assistance for more details regarding these  
accessories, ask your local Makita service center.  
Carbide-tipped saw blades  
General purpose blade for fast and smooth rip,  
crosscuts and miters.  
Combination  
Rip fence (Guide rule)  
Hex wrench 5  
Various type of Makita genuine batteries and chargers  
Plastic case  
14  
 
Memo  
15  
 
Memo  
16  
 
Stamp  
Timbre  
Makita Canada Inc.  
1950 Forbes Street,  
Whitby, Ontario  
L1N 7B7  
Fold  
 
Your answers to the following questions are appreciated.  
1.This product was purchased from?  
3. How did you first learn of Makita Power Tools?  
Hardware/lumber Store  
Tool Distributor  
Industrial Supply  
Other (  
Magazine/Newspaper  
From dealer  
Catalog  
Other (  
)
)
Store display  
2. Use of the product is intended for?  
4. Most favored points are?  
Construction trade  
Home maintenance  
Other (  
Design  
Makita Brand  
Power  
Industrial maintenance  
)
Features  
Size  
Other (  
)
Price  
5. Any comments?  
Certificate of Warranty  
Mail to Makita  
Date Purchased  
Model No.  
Serial No.  
Month  
Day  
Year 20  
Male Female  
Single  
Married  
Initial Last Name  
Street Address  
City  
Province  
Postal Code  
Under 19  
20-29  
30-39  
40-49  
Over 50  
AGE:  
Occupation:  
Dealer's Name & Address:  
 
Paste Paste Paste Paste Paste Paste  
Paste  
Paste  
Factory Service Centres  
Head Office:  
1950 Forbes St., Whitby, Ontario, L1N 7B7  
(905) 571 - 2200 1-800-263-3734  
Regional Office:  
11771 Hammersmith Way, Richmond  
B.C. V7A 5H6  
(604) 272 - 3104 1-800-663-0909  
Regional Office:  
6389 boul. Couture, St. Leonard, Quebec  
(Montreal)  
H1P 3J5  
(514) 323 - 1223 1-800-361-7049  
(902) 468 - 7064 1-888-625-4821  
Dartmouth:  
202 Brownlow Avenue  
Dartmouth, N.S., B3B 1T5  
Ville St. Laurent:  
(Montreal)  
1140 Rue Bégin, Ville St. Laurent, Quebec  
H4R 1X1  
(514) 745 - 5025 1-888-745-5025  
Les Saules:  
(Quebec)  
1200 St. Jean Baptiste, Unit 106, Les Saules,  
Quebec, G2E 5E8  
(418) 871 - 5720 1-800-663-5757  
Nepean:  
(Ottawa)  
210 Colonnade Road, Unit 11, Nepean,  
Ontario, K2E 7M1  
(613) 224 - 5022 1-888-560-2214  
Whitby:  
1950 Forbes St., Whitby, Ontario, L1N 7B7  
(905) 571 - 2200 1-800-263-3734  
London:  
317 Adelaide St. S., Unit 117, London,  
Ontario, N5Z 3L3  
(519) 686 - 3115 1-800-571-0899  
Mississauga:  
Calgary:  
6350 Tomken Rd., Unit 8, Mississauga,  
Ontario, L5T 1Y3  
(905) 670 - 7255 1-888-221-9811  
#8-6115 Fourth St. S.E., Calgary  
Alberta, T2H 2H9  
(403) 243 - 3995 1-800-267-0445  
Edmonton:  
Richmond:  
Winnipeg:  
Saskatoon:  
11614-149 Street, Edmonton, Alberta,  
T5M 3R3  
(780) 455 - 6644 1-888-455-6644  
11771 Hammersmith Way, Richmond, B.C.,  
V7A 5H6  
(604) 272 - 3104 1-800-663-0909  
1670 St. James Street, Winnipeg, Manitoba,  
R3H 0L3  
(204) 694 - 0402 1-800-550-5073  
206A-2750 Faithful Avenue Saskatoon,  
Saskatchewan, S7K 6M6  
(306) 931 - 0111 1-888-931-0111  
For the authorized service centre nearest you please refer to the local yellow pages directory under toolsor con-  
tact our customer service department (Tel) 1-800-263-3734  
CUSTOMER RECORD  
When you need service...  
DATE  
Explain the problem in a letter  
PURCHASED:  
Enclose the letter with the tool  
DEALERS NAME  
Package carefully and send prepaid  
& ADDRESS:  
to the nearest Makita factory or  
authorized service centre  
MODEL NO.:  
SERIAL NO.:  
19  
 
MAKITA LIMITED ONE YEAR WARRANTY  
Warranty Policy  
Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from  
workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during  
this one year period, return the COMPLETE tool, freight prepaid, to one of Makitas Factory or Authorized Service Centres.  
If inspection shows the trouble is caused by defective workmanship or material, Makita will repair (or at our option, replace)  
without charge.  
This Warranty does not apply:  
where normal maintenance is required,  
repairs have been made or attempted by others,  
the tool has been abused, misused or improperly maintained,  
alterations have been made to the tool.  
IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES FROM  
THE SALE OR USE OF THE PRODUCT. THIS DISCLAIMER APPLIES BOTH DURING AND AFTER THE TERM OF THIS  
WARRANTY.  
The Makita Warranty is the only and the entire written warranty given by Makita for the Makita tools. No dealer or his agent  
or employee is authorized to extend or enlarge upon this warranty by any verbal or written statement or advertisement.”  
MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES INCLUDING IMPLIED WARRANTIES OF  
MERCHANTABILITYAND FITNESS FOR A SPECIFIC PURPOSE,AFTER THE ONE YEAR TERM OF THIS WARRANTY.  
This Warranty gives you specific rights. The provisions contained in this warranty are not intended to limit, modify, take away  
from, disclaim or exclude any warranties set forth in any provincial legislation. To the extent required by law, the provisions in  
any provincial or federal legislation with respect to warranties take precedence over the provisions in this warranty.”  
Makita Corporation of America  
2650 Buford Hwy., Buford, GA 30518  
884192B239  
 

Kyocera Printer FS 1035MFP DP User Manual
Lenovo Computer Monitor L1711P User Manual
Lexmark Indoor Fireplace MONTEST User Manual
Lexmark Printer 037 User Manual
LG Electronics Oven LDG3011ST User Manual
Life Fitness Bicycle LC 6500N User Manual
Life Fitness Stepper Machine LS 9100B User Manual
Link electronic Network Router 860 XL165V User Manual
Makita Food Saver VC4710 User Manual
McCulloch Lawn Mower 96041016500 User Manual